Finished write ups go here, If it is a work in progress we can transfer it here later.
http://i1100.photobucket.com/albums/g416/john666boy/ae9027e6.jpg here is the stock bedside with all its rot. After some thought i decided not go go...
Hey folks, I've been working on collecting the missing interior trim pieces as part of my restoration, and currently I'm looking at some rear...
I dont usually cry, but...wahhhh I'm out of ideas on this! If anyone is up to a challenge here it is! 1994 Ford 4.9L I6 IFI driving me to insane...
We have built idle controllers for our powerstroke diesels. Both 1995. It is a pretty simple setup, parts can be bought at Radio shack for less than...
Anyone have a good source for the clear lens that covers the door panel courtesy lights on 1995 trucks? I have searched all my parts catalogs with no...
Well for starters, I knew I had a problem when pulling trailers around the mud and muck only one tire would spin. It got worse and of recent we have...
I'm new to actually working on diesels, but I do have a lot of 351/350 experience. I have a 1989 7.3 Centurion. The head gasket is starting to go....
I will keep adding to this as we get farther into it. It is important to know what was wrong with the transmission when you are about to rebuild...
Prep: 1) You'll need access to all 10 bolts on the door's hinges, which means the fender will have to be at LEAST loose enough to pull out a few...
Hi folks, i haven't been on here for a while, not for any particular reason although sadly i did sell my cabriolet and started my other project which...
Ever since I bought my truck I had been wanting to do something about the useless console that came with my truck. Everything slid off of it and it...
I cant count how many threads I have seen with Ford 4.9L oil pump drive issues after distributor replacement, all with no definitive answer. I know...
It will take me a few days to get this all posted but I'll start with some before and after photos.
I learned the value of an honest mechanic, after getting totally ripped off by a dirt bag. Not going to get into all that here. Long story short,...
My AC compressor is making a lot of noise even without the AC on. I was looking into getting a bypass bracket. But they were more than I wanted to...
Prep: 1) You'll need access to all 10 bolts on each door's hinges, which means the fender will have to be at LEAST loose enough to pull out a few...
Hi guys, Another question, from the new guy.... So I don't know much history on this rig but I will lay down what has been going on over the last...
Alright have a new issue. I have a tapping sound from the passenger side of my engine. My neighbor says it sounds like an exhaust leak coming from...
Hi guys, I just bought a 4dr and I'm rather new when it comes to working on the brake system of a ford truck. I have a couple things going on,...
Hello everyone: Long time looking, first time posting. A great site...... Wanting to know if any one out there has any feed back on any of these...
ok im looking to clean up the rear heat issue it would be nice to get that whole system and the 4 hoses that run along the frame to the rear gona...
Hello Everyone, Well, I did it, a completely brainless act that should at least make me an "honorary" blonde.. I threw out my truck key. ...
This is another way of installing the Selector Knob on a 6 position Chip. I tried a few different places and didn't like where it was. So this is...
http://www.ncspecialties.com/shop/compressorbracket/oasis.htm
Evening everyone. Hope everyone had a great Thanksgiving and enough Tums to get you through. I'm sure that this subject has been dealt with before...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
