Finished write ups go here, If it is a work in progress we can transfer it here later.
I will keep adding to this as we get farther into it. It is important to know what was wrong with the transmission when you are about to rebuild...
This is a list of common automotive terms and their standard meanings, along with some slang & alternate meanings. It also includes most of the...
If you plan to do this, there are some preparatory steps that will make the job easier. Pull your taillights & rinse out that area, and the bottom of...
This thread is a pictorial reference for the removal, rebuilding, and installation of a Ford C6 Transmission. This one just happened to be mated to...
I bought this intercooler a couple years ago now and finally getting it installed. At the time it was the most efficient setup. Better cooling...
This is a repost of info I originally posted to other BBSs, and it was shamelessly plagiarized by BroncoDriver Magazine in 2008. The "PSOM" is...
A Typically the best route to have a 4x4 truck is to get one that is already built from the factory the effort to convert is usually to great to do ...
Well for starters, I knew I had a problem when pulling trailers around the mud and muck only one tire would spin. It got worse and of recent we have...
Everything you never wanted to know about engine cooling Some of this may seem overly simplified, but I'm trying to make it readable by anyone. ...
Too many people don't understand emissions systems, or why they exist, and waste time & effort removing or disabling them. Early systems were...
This thread is locked, I want to keep it strictly installation instructions. If you are researching the conversion, have comments, or questions,...
Prep: 1) You'll need access to all 10 bolts on each door's hinges, which means the fender will have to be at LEAST loose enough to pull out a few...
http://i1100.photobucket.com/albums/g416/john666boy/ae9027e6.jpg here is the stock bedside with all its rot. After some thought i decided not go go...
current dash pictures I dummied up the dash for a preview few shots of the doors progress as well
We have had an oil cooler leaking for a long time, Not horrible but making a mess under the truck. So we finally dug into it. Not a bad job,...
We started to cover this in another thread and thought I would write this up quick. Back ground. In 1988 and 1989 until mid year Ford used a two...
Prep: 1) You'll need access to all 10 bolts on the door's hinges, which means the fender will have to be at LEAST loose enough to pull out a few...
Truck lost the water pump last night which in turn took out both belts and the air pump. Going to tear apart the truck today/tomorrow and g ahead ad...
I have started my Big Fuel tank project. Quick how many cubic inches in a gallon?? I think it is 231, but could not find a conversion chart. I...
So, as I said in another thread, I got my hands on a 93 non-turbo with 135k on it. I didn't get to hear it run but I was assured it was a runner...
So, here it finally is. I'd say I am 95% done, but I figured it was enough to go ahead and post up what I've been working on in the past 8 or 9...
We have built idle controllers for our powerstroke diesels. Both 1995. It is a pretty simple setup, parts can be bought at Radio shack for less than...
I'm new to actually working on diesels, but I do have a lot of 351/350 experience. I have a 1989 7.3 Centurion. The head gasket is starting to go....
We started on this project over the weekend. If any of you wanted to make your own I will post up what we did here. Over all I like the way it...
This mod changes the output voltage to the injectors. It increases it, which essentially will open them faster. Allowing more fuel to get in, in the...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
